Azəricə (Azərbaycan dili)Russian (Русский)English (United Kingdom)

Eposement Y40

EPOSEMENT 40Y ADHESIVE FOR HEAT INSULATION PANELS

Product description

Penoflex®5

ADHESIVE FOR HEAT INSULATION PANELS

Eposement 40y is a modified polymerization technology, cement based adhesive material applied for bonding heat insulation panels.

The product conforms to the requirements of AZS 039-2000 (TS-11140 - 1993) standard “Adhesives – cement based (hydraulic conjunction), suitable for glazed, ceramic, and floor tiles”

Fields of Application

This product can be applied in the following areas:

bonding heat insulation panels in construction works.

Advantages

Perfect adhesive ability;

Easy preparation and application;

Resistant to freezing and warm weather conditions.

Application procedures

Preparation of the surface. Please be careful to the surface to be treated with the product: it should be healthy, dry, dust-free, clean, and smooth; the surface should be totally free of fat and paraffin residues deteriorating adhesive force, and there should not be any splinters. In case the surface has 5-20 mm deep cracks, they should be filled with Eposement repair mixture two days before use. Temperature of the treated surface should not exceed +250C, and it should be dampened.

Preparation of the mixture. Carefully pour 25 kg powder mix into 6.0 - 6.5 liters of water and mix for 3-5 minutes till it is entirely homogeneous. Give the mixture 3-5 minutes to set, mix again during 30-second period, bringing the product to conditions ready for application.

Application. Apply the eposement 40y adhesive with a plaster trowel onto the back side of the heat insulation panels in single line along the edges, and in a circle in the center, then adhere the heat insulation panels onto the surface to the required level in order to provide the required uniform overall surface. After hardening of the Eposement 40y adhesive fasten the heat insulation panels mechanically to the surface using suitable dowel nails. Take care to prevent crust formation on the adhesive applied onto the panel surfaces when bonding heat insulation panels.

Recommendations. After bonding the of heat insulation panels with Eposement 40y adhesive mandatory fix them to the surface with the help of suitable dowel nails. If at the time of adhesive application the ambient temperature exceeds the limits of +50C - +300C range, then the required temperature should be provided. The adhesive should not be used in warm, rainy and windy weather conditions. If product is applied in the open air, the heat insulation panels should be protected from direct sun rays, wind, and rain during 24 hours after application. After the useful life expired the mixture in no case should be diluted with water or fresh product.

Consumption
TheEposement 40y adhesive consumption at 3 mm thickness is 4 kg/m2. Hence, 25 kg of the Eposement 40y adhesive can bond heat insulation panels onto the surface of approximately 6.0-6.5 m2 area.

Shelf Life and Storage Method

The product can be stored during 12 months packed in original sacks in dry conditions on wooden racks, maximum 10 sacks per rack.

Warnings

taking into consideration that Eposement 40y adhesive is a complex composition mixture, immediately rinse it with water in case of contact with skin or eyes;

do not add any substances not indicated in the application instructions;

parameters indicated above have been received on the basis of laboratory tests conducted in the ambient conditions of +230C±20C temperature and 50% + 5% humidity. Depending on the actual ambient conditions these parameters are subject to change.

Warranty and technical support

information indicated in technical specifications is based on scientific and experimental data;

EPO company is responsible for the product quality only;

with the exception of cases of works executed under the supervision of the company specialists, EPO company shall not be liable for any problems occuring due to improper use of the product by other persons;

the company reserves the right to make changes in its product in consequence of scientific-and-technical development;

for technical support and/or more information please do not hesitate to contact the EPO company!

Last Updated (Wednesday, 19 October 2016 08:42)